EXPLORE MORE CATEGORIES
- Home
- »
- Products & Services
- »
- Fosroc Products
Fosroc Products
Offering you a complete choice of products which include fosroc nitobond ep standard, fosroc nitobond ep, fosroc brushbond roofguard, fosroc nitoseal pu40 600 ml, fosroc nitocote sn525 and fosroc renderoc rg.
Fosroc Nitobond Ep Standard
Product Price: Rs 95 / KgGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Liquid |
| Usage/Application | Bonding old and new cementitious substrates |
| Category | Cementitious Waterproofing |
| Coverage | 2.5 m2 per Liter |
| Type | General purpose epoxy bonding agent |
| Brand | Fosroc |
| Pot Life | Min. 120 minutes @ 350 C |
| Tensile Strength | 15 N/mm2 |
| Flexural Strength | 25 N/mm2 |
| Full hardness | 24 Hrs |
| Full Cure | 7 days |
| Overlay time | 3 hrs |
| Compressive Strength | 40 N/mm2 |
| Bond strength | 11N/mm2 |
| Packaging | Available in 1 Litre and 4 Litre |
- General purpose epoxy bonding agent Uses Bonding old and new cementitious substrates. Advantages Can be applied on concrete & mortar substrate Facilitates improvement in mechanical strength Good positive adhesion Description Nitobond EP Std is a two component epoxy bonding agent supplied in pre-weighed quantities for ready on-site mixing and use. Technical Support The company provides a technical advisory source supported by a team of specialists in the field. Properties Pot life Min. 120 minutes @ 350 C Full hardness 24 hrs. Full Cure 7 days Overlay time Upto 3 hrs. Compressive Strength 40 N/mm2 BS 6319 Part 2 Tensile Strength 15 N/mm2 BS6319 Part 7 Flexural Strength 25 N/mm2 BS 6319 Part3 Bond strength ASTM C881 11N/mm2 Below 200 C, above mentioned times will increase. Application Instructions Preparation All surfaces to be treated must be sound, dust-free and clean. All laitence should be removed by wire-brushing or any other suitable means. Surfaces contaminated with oil or grease, shall be cleaned thoroughly to remove such contaminants. Mixing The entire contents of the hardener Can should be poured into the resin container and the two materials thoroughly mixed until a uniform colour is obtained. To facilitate application at temperatures below 100 C the separate components should be warmed in hot water to a maximum of 250 C before mixing. Coating Mixed Nitobond EP Std should be brush applied to the prepared substrate. The new concrete should be placed within 3 hours at 350 C to the Nitobond EP Std coated substrate, when it is still in a tacky state. Cleaning Tools and equipment shall be cleaned thoroughly after use with Nitoflor Sol. Estimating Packaging Available in 1 Litre and 4 Litre. Coverage Actual coverage will depend upon the texture and porosity of the substrates being covered. Typically, 1Litre pack will cover about 2.0-2.5 m2 and 4 litre pack around 8.0 - 10.0m2 . Storage 12 months shelf life when stored under normal wear house conditions below 350 C in unopened containers. Precautions Health & Safety Contact with skin and eyes should be avoided. Gloves should be used when handling these products. If contact with the resin occurs, skin should be washed immediately with strong detergent. A resin removing cream should be used. Eye contamination must be immediately washed with sufficient quantity of water and medical treatment sought
Yes! I am InterestedRequest A Callback
Fosroc Nitobond EP
Product Price: Rs 750 / KgGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Liquid |
| Packaging Size | 1 L |
| Category | Cementitious Waterproofing |
| Type | Epoxy resin concrete bonding agent |
| Shelf Life | Nitobond EP has a shelf life of 12 months |
| Usage/Application | For bonding fresh wet cementitious materials to existing cementitious surfaces |
| Brand | Fosroc |
| Storage Condition | Store in dry conditions in the original unopened packs. If stored at high temperatures, the shelf li |
| Water Absorption | 0.05% |
| Tensile Strength | 30 N/mm2 |
| Compressive strength | 70 N/mm2 |
| Slant Shear Strength | 36 N/mm2 |
- Epoxyresin concrete bonding agent
- Uses
- Specification
- constructive solutions
- For bonding fresh wet cementitious materials to existing cementitious surfaces. For use on horizontal surfaces or on vertical surfaces where mortar or concrete can be supported by formwork. The long ‘open’ life makes it suitable for use with formwork or where additional steel reinforcement has to be fitted. The product is ideal for roads, bridges, pavements, loading bays and factories, and for bonded or granolithic floor toppings. Nitobond EP is equally suited to internal and external applications.
- Advantages
- Nitobond EP may also be used as part of a repair system where a substrate/repair barrier is required or where the substrate is likely to remain permanently damp or wet.
- Can be applied on to dry or damp substrates
- Exhibits high mechanical strength
- Positive adhesion - exceeds that of the tensile strength of the host concrete
- Slow cure allows time to erect steel reinforcement and formwork
- Solvent-free - can be used in enclosed locations
- Description
- Nitobond EP is based on solvent-free epoxy resins containing pigments and fine fillers. It is supplied as a two-component material in pre-weighed quantities ready for on-site mixing and use. The ‘base’ component is white and the ‘hardener’ component is green, providing visual evidence that adequate mixing has been achieved.
- (Nitobond EPFS, suitable for cold weather working, can be made available when specifically requested.)
- Epoxy bonding agent
- The bonding agent shall be Nitobond EP, a two-component solvent-free epoxy resin. The two components shall be differentially pigmented in order to ensure visually that correct mixing has taken place prior to the application
Yes! I am InterestedRequest A Callback
Fosroc Brushbond Roofguard
Product Price: Rs 270 / BagGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Liquid |
| Brand | Fosroc |
| Category | Waterproofing Coating |
| Coverage | 0.4 liter / m2 / coat (Three coat application is recommended). |
| Type | High build fi bre Reinforced Acrylic Elastomeric Waterproofi ng coating for Roofi ng |
| Usage/Application | Waterproofing |
| Tensile Strength | 2.5 Mpa |
| Overcoating time | 12 hours at 27oC |
| Density | 1.50 |
| Elongation ASTM D412 | 75% |
| Pull off Adhesion-ASTM D4541 | 1 Mpa |
| Permeability (mm) | 5 |
- Brushbond Roofguard is high build fi bre reinforced seamless
- waterproofi ng coating suitable for waterproofi ng of old & new
- roofs. It is a polymer based product applied in multiple coats.
- The product can be applied directly on existing concrete,
- brickbat coba, and screed concrete even without removal provided
- the substrates are sound enough for application of the
- coating avoiding the risk of damage to the old roof associated
- while removing of the existing overlays. The product provides
- a seamless, tough durable water resistant coating which can
- withstand light pedestrian traffi c and also has excellent weather
- resistance for exterior applications.
- Advantages
- High Build system provides higher dry fi lm thickness of more
- than 0.8mm.
- The product can applied directly on existing sound concrete,
- brickbat coba, screed concrete even without removal
- No protection screed required eliminating the additional
- weight due to protection layer
- Excellent barrier to carbon dioxide, chloride and sulphate
- ions.
- Allows water vapour to escape from the structure.
- High resistance to the eff ect of long-term weathering,
- Durable in all climate conditions including UV attack.
- Excellent bond to concrete and masonry.
- Good crack accommodation capacity.
- Minimum surface preparation needed and low labour.
- Standards compliance
- Tested to ASTM D4541, ASTM D412, ASTM G154, ASTM E96
- Description
- Brushbond Roofguard is a single component acrylic polymer
- modifi ed, elastomeric fi bre reinforced high build & easy roller
- applied / brushable coating available in diff erent colours for
- application in multiple layers.
Yes! I am InterestedRequest A Callback
Fosroc Nitoseal Pu40 600 Ml
Product Price: Rs 380 / BagGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Liquid |
| Brand | Fosroc |
| Type | PU based Building & Expansion Joint Sealant |
| Usage/Application | Adhesion to most common building materials |
| Skinning time at 20degC / 50%RH | approx 2 hours |
| Cure rate at 20degC / 50% RH | 24 hours 3mm |
| Hardness | Shore A 32 |
| UV resistance | Very Good |
- One part, PU based Building & Expansion Joint Sealant.Nitoseal PU40UsesNitoseal PU40 is suitable for sealing joints in concrete, brickwork, blockwork, precast panels, stone cladding, perimeter sealing around doors and windows, and non traffi cked fl oor joints.AdvantagesAdhesion to most common building materialsSingle component with fast rate of cureEasy to applyUV resistantPrimerless for most applications (see “Priming”)Available in a range of coloursISO11600:2002 Type F 25LM compliantStandards complianceISO11600:2002 Type F 25LMASTM C920-95 Type S, Grade NS, Class 25US Fed Spec TT-S-00230a Type II, Grade NS, Class25DescriptionNitoseal PU40 is a one part, low modulus gun grade elastomeric sealant based on polyurethane technology. Nitoseal PU40 may be applied to joints between 5 and 35mm wide. To minimise stress imposed on the joint sealant, all moving joints should be designed to an optimum width to depth ratio of 2:1 with an overriding minimum depth of 5mm for non-porous surfaces and 10mm for porous surfaces.For joint widths exceeding 35mm, please contact your local Fosroc Technical Service Department.Properties Form Smooth, non- slumping pasteColour For current range contact FosrocSkinning time at approx 2 hours 20ºC / 50%RHCure rate at 20ºC/ 24 hours 3mm 50% RH Application temperature 5ºC to 50ºCHardness Shore “A” 32Movement accommodation factor (MAF) 25% UV resistance Very GoodService temperature range -40ºC to 70ºCApplication instructionsJoint surfaces must be clean, dry and free from frost. Remove all dirt, laitance, loose material and foreign matter. Remove all rust, scale and protective lacquers from metal surfaces.Removal can be achieved by rigorous wire brushing, grinding or grit blasting. When resealing, the existing sealant should be removed from the joint and the arris cleaned back to sound clean concrete. All debris should be removed.Any expansion joint fi ller must be checked to ensure it is tightly packed and no gaps or voids exist at the base of the sealing slot before positioning a bond breaker.The use of a bond breaker is not required in expansion joints containing cellular polyethylene joint fi ller such as Hydrocell XL, Backing rod or Expandafoam. For construction or contraction joints a bond breaker tape or back-up strip must be used.Where a particularly neat fi nish is required, mask the face edges of the joint before sealing and remove immediately after tooling is completed.PrimingA primer is not normally required. In joints subjected to high ovement or where intermittently immersed during service, Fosroc Primer 7 (porous substrates, drying time 30 minutes) or Fosroc Primer 4 (non-porous substrates, drying time 2-5 minutes) is recommended.Prime the joint face using a clean, dry brush. Avoid over application of primer, to prevent causing puddles in the bottom of the joint.
Yes! I am InterestedRequest A Callback
Fosroc Nitocote SN525
Product Price: Rs 850 / BagGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Liquid |
| Brand | Fosroc |
| Coverage | 175 ml/m2 |
| Type | Monomeric silane water repellent penetrant |
| Usage/Application | Markedly reduces water and chloride ingress |
| Purity | 95% |
| Specific Gravity | 0.87 |
| Packaging | 25litre & 200 litre container |
| Refractive index | 1.4 |
- Monomeric silane water repellent penetrant
- Uses
- A deep penetrating treatment designed to protect concrete
- from both water and chloride ingress whilst still permitting water
- vapour transmission (breatheability).
- Advantages
- Markedly reduces water and chloride ingress.
- Deep penetration into substrates.
- Non-staining.
- Increases freeze thaw resistance.
- Minimises effl orescence
- Chemically resistant to de-icing compounds and atmospheric
- contaminants.
- Resistant to alkaline environment.
- Protects hairline cracks upto 0.3mm.
- Standards compliance
- Nitocote SN525 complies to ZTV SIB90 Standards set by
- German ministry.
- Also complies to EN1504 - 2.
- Description
- Nitocote SN525 has a 95% active content of monomeric alkyl
- (isobutyl) trialkoxy silane which penetrates deeply into porous
- substrates and then reacts to produce a bonded hydrophobic
- lining to the pores.
- This treatment markedly reduces absorption of water and
- water-borne salts, but still permits passage of water vapour.
- The treatment is not aff ected by UV light and does not produce
- any discolouration of the substrate.
- Properties
- Specifi c gravity : 0.87
- Purity : Minimum 95%
- Refractive index : 1.4
- Nitocote SN525
- Application instructions
- Preparation
- Surfaces should be dry and free from contamination such as oil,
- grease, loose particles, decayed matter, moss or algal growth,
- Laitance and traces of mould oils and curing compounds,shall
- be removed by mechanical means.
- Protect plants, glass, asphalt, bitumen, plastics and all painted
- surfaces prior to application.
- Application
- In order to obtain the penetrating properties of Nitocote SN525,
- it is important that the correct rates of application and overcoating
- times are observed.
- Nitocote SN525 should be applied evenly by saturation fl ooding
- using a wet spray without misting, working from the bottom up.
- It must be applied by spraying at low pressure and suitable
- nozzel should be used. Brush shouldnot be used for application
- and enough material should be sprayed on the surface during
- the application and wet layers should be observed on surfaces.
- Cleaning
- Equipment should be cleaned with Nitofl or Sol immediately after
- use. Any spillages should be absorbed with sand or sawdust
- etc., and disposed of in accordance with local regulations.
- Estimating
- Packaging
- Nitocote SN525 : 25litre & 200 litre container
- Nitofl or Sol : 5 litre packs
- Coverage and yield
- Nitocote SN525 : 175 ml/m2
- Limitations
- The application of Nitocote SN525 should not commence if
- temperatures are below 5°C and falling or if the concrete surface
- temperature is above 45°C.
- Nitocote SN525 hydrolises with atmospheric moisture. Material
- from opened containers should be used on the same day.
- If rain is expected, application should be avoided. After rain
- complete drying of the substrate is required before application
- of Nitocote SN525.
Yes! I am InterestedRequest A Callback
Fosroc Renderoc Rg
Product Price: Rs 340 / BagGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Powder |
| Packaging Size | 25 Kg |
| Brand | Fosroc |
| Coverage | 13.0 litres per 25 kg bag |
| Usage/Application | Repairs to damaged reinforced concrete elements, particularly where access is restricted and where v |
| Type | General purpose, non-shrink, cementitious micro-concrete |
| Color | Grey |
| Packaging Type | Bag |
| Tensile Strength | 2.0N/mm2 @ 28 days |
| Flexural Strength | 5N/mm2 @ 28 days |
| Young's Modulus | 25 kN/mm2 |
- General purpose, non-shrink, cementitious micro-concrete Uses Renderoc RG is used for repairs to damaged reinforced concrete elements, particularly where access is restricted and where vibration of the placed material is diffi cult or impossible. It is suitable for various structural strengthening measures such as encasement build-ups, jacketing, piletop encapsulation resin system, etc. Advantages Gaseous expansion system compensates for shrinkage and settlement in the plastic state. Can be pumped or poured into restricted locations. Highly fl uid to allow for placement without vibration. Pre-packed to overcome site-batched variations. Rapid strength gain to facilitate early reinstatement. High ultimate strengths and low permeability of cured repair. Contains no chloride admixture. Ensures piletop integrity as part of a waterproofi ng system
- Renderoc RG is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-fl owing non-shrink repair micro concrete. The material is based on Portland cements, graded aggregates and fi llers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand. The low water requirement ensures high early strength and long-term durability. For larger repairs, the mixed Renderoc RG may be modifi ed by the addition of 5mm to 12mm clean, graded, saturated surface dry aggregates at site. For exceptionally large repairs, the local Fosroc offi ce shall be consulted. Technical support Fosroc off ers a technical support package to specifi ers, end users and contractors as well as technical on-site assistance in locations all over the country.
Yes! I am InterestedRequest A Callback
Fosroc Renderoc Plug
Product Price: Rs 280 / BagGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Powder |
| Brand | Fosroc |
| Category | Cementitious Waterproofing |
| Type | Rapid setting cement-based, water-stopping mortars |
| Color | Grey |
| Usage/Application | Emergency Water Stopping |
| Packaging Size | 25 Kg |
| Shelf Life | The product has a shelf life of 12 months from the date of manufacture if kept in dry storage in the |
- Rapid setting cement-based, water-stopping mortars conforming to the requirements of BS EN 1504 Class R1 Uses For the rapid patching and plugging of concrete segments, concrete and brick tunnel linings, sewage systems, below ground access chambers, pipes, basements, foundations and mines. Advantages Emergency water-stopping capability Single component Excellent bond to the substrate Low exotherm minimises thermal cracking Pre-bagged to overcome variations in site batching Chloride-free Renderoc Plug 20: Approved for use in public water supplies Renderoc Plug 20 : BS6920 listed product. Description Renderoc Plug are rapid setting mortars which are easy to apply to horizontal, vertical or overhead surfaces at a wide range of thicknesses. There are two grades available: Renderoc Plug 1 with an initial set time of approximately 1 minute, and Renderoc Plug 20 with an initial set time of approximately 20 minutes. (Set times are based on ambient/substrate temperatures of 20°C.)
- Application instructions Preparation Areas to be patched should be cut back to a depth of 15 mm and given a good mechanical key. Feather-edges must not be allowed. Surface should be brushed clean to remove loose material, dust and laitance. Grease, slime or mould growth should be removed by steam cleaning or high-pressure water jetting. A proprietary degreasing agent should be used for removal of light oil or grease contamination. To seal leaks, crack openings must be chased out to approximately 20 mm square. The chase should always be undercut to avoid leaving a v-section. All loose material and debris should be removed. Mixing Renderoc Plug should be added to clean water in the following proportions: One part clean water to three parts Renderoc Plug (by volume). Mix to a stiff consistency in a suitable mixing vessel, using a trowel or gloved hand. Due to the rapid set characteristics of the product, only prepare a quantity of mortar which can be placed within the prescribed set time. Application Trowel apply or hand-knead the mixed mortar in place, ensuring maximum contact with the substrate before the material sets. No priming system is required but the substrate must be in a saturated surface dry state before application. If being used to plug running water, Renderoc Plug 1 should be used and held in place until the initial set is reached. The minimum application thickness of Renderoc Plug products is 15 mm. Low temperature working In cold conditions down to 1°C, the use of warm water (up to 20°C) is advisable to accelerate strength development. Normal precautions for winter working with cementitious materials should be adopted. The material should not be applied when the substrate and/or air temperature is 1°C and falling. At 1°C static temperature or at 1°C and rising, the application may proceed. Set and cure times will be increased at low temperatures. If in doubt contact the local Fosroc office. High temperature working At ambient temperatures above 35°C, the material should be stored in the shade and cooler water (down to 20°C) used for mixing. Set and cure times will be reduced at high temperatures. Curing For UK wholesome water purposes where contracts require DWI or WRAS certifications, Renderoc Plug 20 should be mixed, applied and cured in accordance with the manufacturer’s Instructions For Use sheet (contact Fosroc Technical Helpdesk). Cleaning Renderoc Plug products should be removed from equipment with clean water prior to the initial set. Cured material can only be removed mechanically. Estimating Renderoc Plug 1 is supplied in 6 kg bags each yielding 3 litres. Renderoc Plug 20 is supplied in 25 kg bags each yielding 12.5 litres.
Yes! I am InterestedRequest A Callback
Fosroc Cebex 200
Product Price: Rs 360 / KgGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Powder |
| Usage/Application | Admixture for cement grouts |
| Brand | Fosroc |
| Setting Time | Cebex 200 may slightly retard the setting times of cement based grouts depending on the cement and a |
| Compatibility | Cebex 200 is compatible with all types of portland cement. Cebex 200 may be used in mixes containing |
| Packing | Cebex 200 is supplied in 225 gm packs. |
| Storage | 6 months |
- Plasticising and hydrogen free expansion grout admixture Uses Cebex 200 is an admixture for cement grouts where a reduced water / cement ratio and positive expansion are required. Applications include bed grouting, duct grouting, non-shrink infilling and jointing. Advantages Hydrogen free expansion system compensates for plastic shrinkage and settlement in properly designed cementitious grout. Reduced water / cement ratio in the grout mix ensures low permeability and long term durability in service. Gives high grout fluidity with low water / cement ratio, thus making placement or injection of the grout easy. No metallic iron content to corrode and cause staining or deterioration due to rust expansion in the grout. Composition allows high early strength development in grouts, without the use of chlorides. Description Cebex 200 a plasticising and hydrogen free expansion grout admixture is supplied as a powder admixture. Cebex 200 allows the use of a reduced water / cement ratio with consequent increased strengths and durability. The expansive medium counteracts the natural settlement and plastic shrinkage of the grout and aids stability and cohesion. Technical Support Fosroc offers a comprehensive range of high performance, high quality concrete repair and construction products. In addition, Fosroc offers technical support service to specifiers, end-users and contractors, as well as on-site technical assistance in locations all over the country.
Yes! I am InterestedRequest A Callback
Fosroc Conbextra Gp2n
Product Price: Rs 430 / BagGet Best Price
Product Brochure
Product Details:
| Packaging Size | Kg |
| Usage/Application | Construction |
| Type | Free flow , high strength, non-shrink, cementitious precision grout |
| Yield | Pourable Flowable Yield ( litres) 15.6 and 15.8 |
| Packaging Type | HDPE Bag |
| Country of Origin | Made in India |
| Tensile strength | 3.5N/mm2 @ 28 days |
| Time for expansion | Start : 20 minutes (after mixing ) Finish : 120 minutes |
| Unrestrained expansion | 4 % in the plastic state enables to overcome shrinkage |
- Free flow , high strength, non-shrink, cementitious precision grout Uses Conbextra GP2(N) is used for precision grouting where it is essential to withstand static and dynamic loads. Typical applications would be the grouting of base plates of turbines, compressors, boiler feed pumps etc., It can also be used for anchoring a wide range of fixings. These include masts, anchor bolts and fence posts. Advantages Gaseous expansion system compensates for shrinkage and settlement in the plastic state No metallic iron content to cause staining Pre-packed material overcomes onsite batching variations Develops high early strength without the use of chlorides High ultimate strength ensure the durability of the hardened grout Free flow ensures high level of contact with load bearing area Description Conbextra GP2(N) is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non-shrink grout for gap thicknesses up to 100mm. Conbextra GP2(N) is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded fi llers are designed to assist uniform mixing and produce a consistent grout
Yes! I am InterestedRequest A Callback
Fosroc Reebaklens RR
Product Price: Rs 125 / LitreGet Best Price
Product Brochure
Product Details:
| Packaging Size | Reebaklens RR cleaning agent is available in 1/2, 1, 5 L containers |
| Usage/Application | Industrial |
| Packaging Type | Bottle |
| Physical State | Liquid |
| Brand | Buzil |
| Quantity Per Pack | 5 Liter |
| Shelf Life | At least 1 year in original sealed containers under normal warehouse conditions. |
| Coverage | 2.5 m2/L |
- Rust remover, cleaning and etching agent
- Uses
- Reebaklens RR is used as a rust remover from steel bars prior
- to encasing in concrete / microconcrete. It can also be used
- on other steel surfaces prior to coating with epoxy systems.
- Advantages
- Rapid action
- Safe with metals (except zinc and galvanised steel), wood,
- glass, plastic and rubber. No corrosive action. Penetrates oil
- and grease.
- Description
- Reebaklens RR cleaning agent is a combination of acid based
- material, corrosion inhibitors and dispersing agents and is
- supplied as a clear green solution.
- Technical Support
- Fosroc provides a technical advisory service to specifi ers, endusers
- and contractors as well as on-site technical assistance
- in locations all over the country.
- Properties
- Specifi c gravity : 1.16 - 1.22 @ 250C
- Application instructions
- For rusted metal (iron base)
- Apply Reebaklens RR with brush for complete wetting of rusted
- metal surface and allowed to react it for 16-24 hours. After
- 24 hours, a white layer will appear which will protect further
- corrosion of metal / steel for about 5-7 days. Before applying
- protective coating, the surface should be wire brushed and
- thoroughly cleaned for dust with dry cloth.
- Removal of rust and mill scale
- Prewet the fl oors, then using a stiff bristle broom, brush the aff ected
- areas with a solution of Reebaklens RR cleaning agent and
- water. Strength of the solution required will vary but should be
- between 1 : 1 and 1 : 4 (Reebaklens RR cleaning agent to
- water).
- When the action has fi nished, wash down thoroughly with clean
- water. Wire brush again to remove remaining loose material
- and fi nish by thoroughly washing down with clean water. Repeat
- if necessary. High degree of rust or scale can be removed
- by soaking in the Reebaklens solution for 60 minutes.
- Estimating
- Coverage
- Approx. 2.0 - 2.5 m2/L
- Note : Coverage depends on the rusted area and the depth
- of deposition
- Packaging
- Reebaklens RR cleaning agent is available in 1/2, 1, 5 L
- containers
- Storage
- Shelf life
- At least 1 year in original sealed containers under normal
- warehouse conditions.
- Precautions
- Health & Safety
- Reebaklens RR cleaning agent is acid based and should be
- handled with care. It attacks zinc, aluminium and putty. If in
- doubt about its eff ect on a material, test a small area before
- application.
- Avoid contact with skin. Rubber gloves and goggles should
- be worn. Wash spillages with plenty of water. Enclosed areas
- should be well ventilated. If contact with eyes occur, wash
- immediately with water and seek medical advice.
- Fire
- Reebaklens RR cleaning agent is non fl ammable
- Additional information
- Technical data and guidance can be provided on a
- wide range of admixtures, concreting aids, grouts, repairs,
- protective coatings and the Nitoflor range of
- metallic floor hardeners, epoxy floor coatings and self
- levelling fl oor toppings, epoxy heavy duty abrasion resistant
- screeds.
- Separate datasheets are available on these products
Yes! I am InterestedRequest A Callback
Fosroc Nitobond AR Standard
Product Price: Rs 340 / BagGet Best Price
Product Brochure
Product Details:
| Form of Chemical | Liquid |
| Brand | Fosroc |
| Category | Cementitious Waterproofing |
| Color | White |
| Usage/Application | For improving and bonding floor toppings, mortars and renders |
| Packaging Size | 20 L |
- Latex Acrylic polymer based cement modifier cum bonding aid with waterproofing property Uses For improving and bonding floor toppings, mortars and renders As a bonding agent for Renderoc and other cementitious mortars Polymer modified mortars and screeds for reinstatement of worn out/damaged concrete Polymer modified concrete for improving the impermeability and there by enhancing the waterproofing property Advantages Good adhesion - Provides good bond to concrete, masonry, stone work, plaster and block work. Increased strength - Improves tensile and flexural properties of mortar. Versatile - Compatible with all common hydraulic cements User friendly - application by brush/spray Improves cohesion - No bleeding and segregation Description Nitobond AR Std. is a single component latex acyrlic polymer emulsion used as bonding aid cum cement modifier with waterproofing property. Technical support Fosroc offers technical support service to specifiers, end users and contractors, as well as on-site technical assistance in locations all over the country
Yes! I am InterestedRequest A Callback
Fosroc Conbextra Gp2
Product Price: Rs 480 / BagGet Best Price
Product Brochure
Product Details:
| Packaging Size | 30 kg |
| Usage/Application | Commercial |
| Type | Free flow, high strength, non-shrink, cementitious precision grout |
| Yield | Pourable 12.5 Flowable 13.3 litres |
| Country of Origin | Made in India |
| Brand | Fosroc |
| Model | Conbextra Gp2 |
- Free flow, high strength, non-shrink,
- cementitious precision grout
- Uses
- ConbextraGP2 isusedforprecision grouting where it is essential to withstand static and dynamic loads. Typical applications would be the grouting of base plates of turbines, compressors, boiler feed pumps etc., It can also be used for anchoring a wide range of fixings. These include masts, anchor bolts and fence posts.
- Advantages
- Gaseous expansion system compensates for shrinkage and settlement in the plastic state
- No metallic iron content to cause staining
- Pre-packed material overcomes onsite batching variations
- Develops high early strength without the use of chlorides
- High ultimate strength ensure the durability of the hardened grout
- Free flow ensures high level of contact with load bearing area
- Description
- Conbextra GP2 is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non-shrink grout for gap thicknesses up to 100mm.
- Conbextra GP2 is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded fillers are designed to assist uniform mixing and produce a consistent grout
Yes! I am InterestedRequest A Callback
Fosroc Brushbond Rfx
Product Price: Rs 145 / KgGet Best Price
Product Brochure
Product Details:
| Brand | Fosroc |
| Packaging Size | 15kg + 5.088kg Pack |
| Category | Cementitious Waterproofing |
| Coverage | 14m2 |
| Type | High performance elastomeric cementitious waterproof coating |
| Usage/Application | Waterproofing |
| Pot Life | 30 min @ 27 deg C |
| Toxicity | Non-toxic |
| Colour | Grey |
| Application temp. | Not less than 10 deg C |
| Adhesion to concrete | 1N/mm2 |
| Static crack accommodation : | 1mm |
- High performance elastomeric cementitious waterproof coating Uses Brushbond RFX is an high performance elastomeric cementitious coating used for waterproofi ng and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water. Brushbond RFX is suitable for all types of structures including those in coastal environments. The product can be used on concrete, brick and blockwork substrates and is equally suitable for new and existing structures. The product is designed to reface and even out variations in concrete and masonry surfaces and bridge shrinkage cracks. It provides a seamless, fl exible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements, roofs, toilets & wet areas. The product provides a tough durable water resistant coating which can withstand light pedestrian traffi c and also has excellent weather resistance for exterior applications. Advantages Ex celle nt b arrie r to carbo n dioxide, chloride and sulphate ions. Allows water vapour to escape from the structure. Waterproof-suitable for water retaining structures. High resistance to the effect of long-term weathering, durable in all climate conditions including UV attack. Non toxic - ideal for potable water tanks. Flexible, with thermal expansion similar to concrete. Excellent bond to concrete and masonry. Good crack accommodation capacity. Minimum surface preparation needed and low labour costs. Standards compliance Tested to ASTM D4060, ASTM D4541, ASTM D638, ASTM C836. Description Brushbond RFX is a two component acrylic polymer modifi ed cementitious coating which consists of Brushbond RFX powder and Brushbond RFX liquid acrylic emulsion. It requires only the addition of clean water at site to produce an easily brushable coating. Brushbond RFX can simply be applied by stiff brush, roller or trowel to obtain the desired thickness. Technical Support Fosroc offers technical support service to specifi ers, endusers and contractors, as well as on-site technical assistance in locations all over the country. Properties Pot life : 30 min @ 270C Mixed density : 1.68g/cc (b rushable consistency) Brushbond RFX Colour : Grey Application temp. : Not less than 100C Adhesion to concrete : >1N/mm2 Toxicity : Non-toxic Static crack accommodation : 1mm Application Instructions Surface Preparation All surfaces which are to receive the coating must be free from oil, laitance, grease, wax, dirt or any other form of foreign matter which might affect adhesion. Typically concrete surfaces can be cleaned using high pressure water jet or grit blasting or by proper wire brushing Spalled surfaces or those containing large blow holes, cracks and other such defects should be repaired using Renderoc concrete repair mortars. For further advice on suitable repair mortars, contact the local Fosroc Offi ce. Mixing Brushbond RFX liquid concentrate should be poured into a plastic container or metal drum. Clean fresh water is added in the proportions shown below and mixing commenced with a propeller agitator attached to a slow speed drill (500pm). The powder component should be added gradually to the liquid to avoid lump formation and mixed for 2-4 minutes. Brushbond RFX should be immediately used after mixing. Do not mix more material than can be used within the pot life. Keep stirring Brushbond RFX during the application Mixing ratio Brushbond RFX Brush Application Components Indl Pack Small Brushbond RFX powder 15kg 5kg Brushbond RFX liquid 5.088kg 1.71kg Water 3L 1L Application For best results, surfaces should be damp. In order to obtain the protective properties of Brushbond RFX, it is important that the correct rates of application are observed. Use a short stiff brush preferably 120-150mm width and apply the mixed material like paint.
Yes! I am InterestedRequest A Callback
Fosroc Nito Zinc Primer
Product Price: Rs 90 / LitreGet Best Price
Product Brochure
Product Details:
| Packaging Size | 1 & 5 litre Pack |
| No. Of Components | Two Component |
| Brand | Fosroc |
| Usage/Application | Steel reinforcement primer |
| Grade Standard | Chemical Grade |
| Color | Grey |
| Packaging Type | Can |
| Form | Liquid |
| Shelf Life | 6 months if kept in dry store in the original, unopened containers |
| Is it Anti Corrosive | Yes |
| Specific gravity | 1.75 |
| Recommended thickness per coat | 40 microns (DFT) |
| Application thickness | 100 microns (wet) per coat |
| Drying times | 45 mins |
- Uses Nitozinc Primer is recommended for priming exposed steel reinforcement for use with Fosroc concrete repair mortars. The product actively resists corrosion within the confines of the repair location and avoids the generation of incipient anodes in immediately adjacent locations. Nitozinc Primer is compatible with all Renderoc mortars and fluid micro concretes. Advantages Anti corrosive - Active 'Zinc-rich' system combats corrosion by electro chemical means. Two component product - Easy to mix and use. Timesaving - Touch dry after 30 to 45 mins. Excellent adhesion - Exhibits excellent bond strength in cementitious repairs. Description Nitozinc Primer is supplied as a two component system based on metallic zinc and epoxy resin which on mixing gives a grey coloured liquid. Technical support Fosroc offers a comprehensive range of high performance, high quality concrete repair and construction products. In addition, Fosroc offers technical support service to specifiers, end-users and contractors, as well as on-site technical assistance in locations all over the country. Design Criteria One or two coats of Nitozinc Primer are generally required, dependent largely on the nature and profile of the substrate. Nitozinc Primer is recoatable generally between 30 minutes and one hour after the application of first coat. Application of top coat may also proceed at this time. At elevated temperatures, the recoatable and overlay times will be reduced. The minimum application temperature for Nitozinc Primer is 100 C. The local Fosroc office may be consulted for further information.
Yes! I am InterestedRequest A Callback
Reebol Emulsion Xtra
Product Price: Rs 180 / BottleGet Best Price
Product Brochure
Product Details:
| Usage/Application | Stain free release of concrete moulds |
| Coverage | 1 litre of Reebol Emulsion Xtra when diluted with 6 litres of water will cover 80 to 180 m2 dependin |
| Standard | ISI |
| Physical State | Liquid |
| Packaging Size | Reebol Emulsion Xtra is supplied in 5,20 and 200 litre containers |
| Brand | Fosroc |
| Type | Concentrated and emulsifi ed chemical mould release agent |
| Shelf Life | 12 months |
| Specific Gravity | 0.96 at 270C |
| Grade | Technical Grade |
| Packaging Type | Drum |
| Color | White |
| Country of Origin | Made in India |
- Concentrated and emulsifi ed chemical mould release
- agent
- Uses
- For easy and stain free release of concrete moulds and formwork
- of all types. Particularly where wooden formwork is used
- and de-moulding or stripping times exceed 24 hours.
- Advantages
- Non-staining : No cleaning of unsightly oil stains if plastering
- is not required.
- High quality : Produces really fair faced fi nish concrete.
- Versatile : Can be used on all types of moulds.
- Minimises cleaning : Makes cleaning of form faces between
- pours very easy.
- Concentrate form : Reduces storage and transport costs.
- Water based : Only requires water for dilution.
- Aids corrosion inhibition
- Description
- Reebol Emulsion Xtra is supplied as a pale amber liquid which
- turns emulsifi er when diluted with water to produce a chemical
- release agent, combining the outstanding release properties of
- such materials with the economy of a conventional oil. It reacts
- with the alkali in the concrete to form a thin water repellent skin
- on the surface of the mould which enables easy stripping from
- the hardened concrete.
- Technical Support
- Fosroc off ers a comprehensive range of high performance, high
- quality concrete repair and construction products. In addition,
- Fosroc off ers technical support service to specifi ers, end-users
- and contractors, as well as on-site technical assistance in locations
- all over the country.
- Properties
- Dilution rate - 1 part Reebol Emulsion Xtra: 6parts clear water
- (by volume)
- Formwork surfaces - May be used on wooden or metal
- surfaces. Particularly eff ective on resinous coated surfaces
- including Reebol Formcote coated wooden surfaces.
- Non-staining - Can be used safely with white cement.
- Specifi c Gravity - Typically 0.93 to 0.96 at 270C
- Application instructions
- Mixing
- First dilute Reebol Emulsion Xtra concentrate in the proportion
- of 1:6 with water, using a clean container and stirring thoroughly
- until evenly mixed. If the solution is not used the same day, it
- should be stirred again before use and may require very good
- stirring after 5 days.
- New Moulds : No preparation is normally necessary Metal
- moulds showing signs of rust, must be wire brushed or treated
- with emery cloth and burnished clean before coating.
- New timber : Plywood will give superior results and much
- extended re-use if fi rst coated with Reebol Formcote.
- Used moulds : Must be thoroughly clean and free from
- old concrete, dirt, cement laitence, old mould oil and other
- contaminations. Use a strong detergent for removal of oil
- and grease; Reebaklens for cement and concrete deposits.
- Application : Apply the Reebol Emulsion Xtra 1:6 water dilution
- to the face of the formwork by spray, brush or cloth. Only one
- coat should be applied ( as thinly as possible except on very
- absorbent new timber where two coats may be necessary for
- the fi rst application only ) and allow to dry.
- If the formwork is not used for several days, a further coat
- may be applied.
- Only a very thin fi lm of Reebol Emulsion Xtra should be applied.
- Excess could lead to surface dusting of the concrete.
- The best results are obtained by applying with a fi ne mist
- sprayer. Where a cloth is used, it should fi rst be soaked in
- the release agent and then squeezed out well before applying.
Yes! I am InterestedRequest A Callback